PrusaSlicer

Print settings

Filament settings

<p>The&nbsp;<strong>Maximum&nbsp;volumetric&nbsp;speed&nbsp;setting (MVS)</strong> is one of the <strong>most powerful features in PrusaSlicer</strong>. The MVS setting essentially creates a manager for the maximum amount of filament that the slicer will attempt to push through your 3D printer&rsquo;s hotend.</p>
<p>This gives PrusaSlicer users a <strong>huge advantage</strong>. Rather than trying to calculate a range of speeds for combinations of different nozzle sizes, layer heights or extrusion widths, you can simply specify the speeds and settings you desire, then let MVS regulate speeds at slice time when and only if necessary.</p>
<p>Max volumetric speed = Layer Height &times; Extrusion Width &times; Speed</p>
<p>Independent MVS values can be set under both <strong>Print settings</strong> and <strong>Filament settings</strong>. In your print profile, you'll typically have an all-around default value based on your hotend hardware. In filament profiles, you can adjust MVS as needed to account for filament characteristics, e.g. decrease it for FLEX filaments (so you won't have to create a new print profile for flexible filaments, just a filament profile).</p>
<div class="tip-callout">Set MVS to <strong>zero</strong> (0) for <strong>no limit</strong>.</div>
<div>
<div class="note-callout">MVS is sometimes referred to as auto-speed (auto speed).</div>
</div>
<h4>MVS in Print settings</h4>
<p><strong>Print settings - Speed - Max volumetric speed</strong> (Expert mode)</p>
<p>This value sets the overall maximum volumetric speed. Even if you set MVS to a higher value in filament settings, it will never exceed this value.</p>
<p><img decoding="async" loading="lazy" style="display: block; margin-left: auto; margin-right: auto;" src="https://cdn.help.prusa3d.com/wp-content/uploads/volumetric_print.png" sizes="100vw" srcset="https://cdn.help.prusa3d.com/wp-content/uploads/volumetric_print-300x122.png 300w, https://cdn.help.prusa3d.com/wp-content/uploads/volumetric_print-600x244.png 600w, https://cdn.help.prusa3d.com/wp-content/uploads/volumetric_print-768x313.png 768w, https://cdn.help.prusa3d.com/wp-content/uploads/volumetric_print-800x326.png 800w" alt="" width="599" height="244"></p>
<h4>MVS in Filament settings</h4>
<p><strong>Filament settings - Advanced - Max volumetric speed</strong>&nbsp; (Advanced mode)&nbsp;</p>
<p>This value is capped by MVS set in the Print settings, you can, however, override it to a lower value.</p>
<p><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/volumetric_filament.png" sizes="100vw" srcset="https://cdn.help.prusa3d.com/wp-content/uploads/volumetric_filament-300x163.png 300w, https://cdn.help.prusa3d.com/wp-content/uploads/volumetric_filament-600x327.png 600w, https://cdn.help.prusa3d.com/wp-content/uploads/volumetric_filament-768x418.png 768w, https://cdn.help.prusa3d.com/wp-content/uploads/volumetric_filament-800x436.png 800w" alt=""></p>
<div>
<div class="note-callout">Much of the time, neither linear speeds nor max volumetric speed matter when doing small prints. The nozzle never comes up to full speed and spends most of the time speeding up and slowing back down at lower speeds. It&rsquo;s when you start doing larger parts or moving fast for things like infill that it matters. &ldquo;Obeying the speed limit&rdquo; with the max volumetric speed setting avoids extruder clicks and jams that can spell disaster mid-way through a large print.</div>
<h3>Choosing MVS</h3>
<h4>Filaments</h4>
<p>Different filament materials have different characteristics. Viscocity, stiffness and other factors may greatly reduce effective throughput.</p>
<p>Examples:</p>
<table class="striped" style="border-collapse: collapse; width: 100%;" border="0">
<tbody>
<tr style="height: 18px;">
<th style="width: 50%; height: 18px;"><strong>Filament</strong></th>
<th style="width: 50%; height: 18px;"><strong>Max volumetric speed (approx.)</strong></th>
</tr>
<tr style="height: 18px;">
<td style="width: 50%; height: 18px;">PLA</td>
<td style="width: 50%; height: 18px;">15</td>
</tr>
<tr style="height: 18px;">
<td style="width: 50%; height: 18px;">ASA/ABS</td>
<td style="width: 50%; height: 18px;">11</td>
</tr>
<tr style="height: 18px;">
<td style="width: 50%; height: 18px;">PETG</td>
<td style="width: 50%; height: 18px;">8</td>
</tr>
<tr style="height: 18px;">
<td style="width: 50%; height: 18px;">BVOH/PVA (soluble supports)</td>
<td style="width: 50%; height: 18px;">4</td>
</tr>
<tr style="height: 18px;">
<td style="width: 50%; height: 18px;">FLEX (TPU/TPE)</td>
<td style="width: 50%; height: 18px;">1-2.5</td>
</tr>
</tbody>
</table>
<h4>Hotends</h4>
<p>The overall maximum volumetric speed you should use depends on your hotend. The E3D V6 hotend that ships with the Original Prusa i3 MK3/S is advertised with a rate of 15 mm<sup>3</sup>/s. A safe value that leaves some space for imperfect setup (idler tension, slightly jammed nozzle) of 11.5 mm<sup>3</sup>/s is realistic.</p>
<p>If you need to push more filament, a more powerful hotend will be necessary. The Volcano hotend from E3D increases this to roughly 25 mm<sup>3</sup>/s but does require modding the printer and the firmware. Other hotend designs allow even higher flow rates.</p>
<h4>Nozzle diameter</h4>
<p>Intuitively, it may seem that the nozzle diameter shouldn't affect the maximum amount of plastic that the hotend can heat in a given amount of time. However, <strong>with bigger nozzles, you can slightly increase MVS</strong> due to lower mechanical resistance - basically, it's a bit easier for the filament to get pushed through the nozzle.</p>
<p>And vice-versa, with smaller nozzles, you'll have to decrease MVS a bit.&nbsp;</p>
<div class="tip-callout">With larger nozzles, consider increasing the nozzle temperature to allow for even bigger MVS. E.g. you can print PLA 10-20 &deg;C hotter than our standard profile when using a 0.6 mm nozzle.</div>
<div>
<div class="tip-callout"><strong><strong>Does printing with large diameter nozzle and tall layer height actually save print time?</strong></strong></p>
<p>This is an often-overlooked consequence of MVS. When you use a large diameter nozzle and very tall layer height, e.g. 0.8 mm nozzle and 0.5 mm layer height, <strong>your print speed is indeed going to be capped by MVS</strong>. That is unless you install a more powerful hotend on your printer. If you notice in the preview, that your speed is limited by MVS, you can try increasing the nozzle temperature and raising MVS a bit. However, it may be time to simply lower the layer height, you'll get more detail without increasing the print time because the printer will be able to print faster.</p>
</div>
<div>&nbsp;</div>
</div>
<h3>Preview MVS</h3>
<p>Once you slice your model, you can switch the preview mode to&nbsp;<em>Volumetric flow rate&nbsp;</em>using the select box in the bottom left corner.</p>
<p>On smaller models, you'll notice you're not being capped by MVS at all. Likewise, if you're printing with small layer height, you're most likely not going to be capped by MVS.&nbsp;</p>
<p>On the other hand, when printing bigger models with tall layer heights, you may notice the speed being limited by MVS, especially when printing infill. If the majority of your model is being printed slower due to the MVS limit, consider lowering the layer height, you'll get more detail "for free".</p>
<p><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/preview_volumetric.png" sizes="100vw" srcset="https://cdn.help.prusa3d.com/wp-content/uploads/preview_volumetric-300x147.png 300w, https://cdn.help.prusa3d.com/wp-content/uploads/preview_volumetric-600x293.png 600w, https://cdn.help.prusa3d.com/wp-content/uploads/preview_volumetric-768x375.png 768w, https://cdn.help.prusa3d.com/wp-content/uploads/preview_volumetric-800x391.png 800w" alt=""></p>
<p style="text-align: right;"><em>Big thanks to <strong>Bob George</strong> for his help on this article</em></p>
</div>


Max volumetric speed

<p>As soon as the melted plastic leaves the nozzle, it's no longer under the precise control of the extrusion system. There are two problems to consider:</p>
<ol>
<li>Printing must always be done on an <strong>already solidified layer</strong>, otherwise, the previously extruded plastic will be moved around and distorted by the new layer</li>
<li>When printing <strong>overhangs</strong> or <strong>bridges</strong>, it's important to freeze and solidify the plastic in place as soon as possible. Otherwise, the filament will sag down.</li>
</ol>
<p>Most 3D printers come with a dedicated <strong>print fan</strong>. By blasting ambient air at the extruded filament, the cooling can be dramatically improved. However, with some materials, this could make things actually worse and cause warping or layer separation. PrusaSlicer lets you adjust the cooling settings for each filament.</p>
<h4>Keep fan always on</h4>
<p>The print fan will always maintain at least a minimum speed. <strong>This setting is typically on</strong> for most materials with the exception of ABS, ASA, PC, and some flexibles.</p>
<h4>Enable auto cooling</h4>
<p>When enabled, the cooling fan and print speed will change during the print based on the settings below. A text description below will <strong>update with every change of any cooling setting</strong> and will explain in detail the resulting cooling behavior.</p>
<p><img decoding="async" style="display: block; margin-left: auto; margin-right: auto;" src="https://cdn.help.prusa3d.com/wp-content/uploads/2024/07/c3e0f8af741ce8d43517b269666d6bb5.jpg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Cooling REVIEW" alt="" width="700" height="505" loading="lazy" /></p>
<p>When disabled, the print fan will run at a fixed speed the whole time defined by <strong>Fan speed - Min</strong> with the exception of bridges, which can still be defined by <strong>Bridges fan speed</strong>.</p>
<h3>Fan settings</h3>
<h4>Fan speed</h4>
<p>You can set <strong>Min</strong> and <strong>Max</strong> fan speed as a percentage of the fan's max RPM. </p>
<p>The <strong>Max</strong> value will be used when the layer print time is below the <strong>Slow down if layer print time is below</strong> value.</p>
<p>The <strong>Min</strong> value will be used when the layer print time is longer than <strong>Enable fan if layer print time is below</strong> value.</p>
<p>If the layer print time is between these two values, the fan speed will run <strong>proportionally</strong> at a speed between the <strong>Min</strong> and <strong>Max</strong> value.</p>
<p>This may seem a bit confusing, but you can use the live-updating text description above Fan settings, which will hopefully make everything clear. Try changing the values and see how the description changes.</p>
<h4>Bridges fan speed</h4>
<p>Overrides the fan speed with set value when printing <strong>bridges and overhangs</strong>. Typically you'll set this to a higher value compared to normal printing.</p>
<h4>Disable fan for the first X layers</h4>
<p>Cooling the very first layer is usually <strong>not necessary</strong>, as it's being laid on a flat surface. With many filaments, you may even want to skip cooling for a few more first layers (typically between 1-5) to prevent warping and detaching the print from the print bed, which would inevitably lead to a ruined print.</p>
<h3>Dynamic fan speeds</h3>
<p>The setting enables and controls dynamic, variable fan speed in function of the overlap percentage. </p>
<p>The overlap percentage represents the overlap of extrusion with the previous layer. A 100% overlap is a full overlap (no overhang), while a 0% overlap represents a full overhang (floating extrusion, bridge). </p>
<p>The input fan speed values represent the percentage of the fan's max RPM. </p>
<p>Fan speeds for overhang sizes in between are calculated via linear interpolation. </p>
<p><img decoding="async" style="display: block; margin-left: auto; margin-right: auto;" src="https://cdn.help.prusa3d.com/wp-content/uploads/2024/07/92654b09a66c9d2587f65cae1b76f073.jpg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Cooling REVIEW" alt="" width="700" height="494" loading="lazy" /></p>
<h3>Cooling thresholds</h3>
<h4>Enable fan if layer print time is below</h4>
<p>If the layer print time is estimated below this number of seconds, the print fan will be enabled and its speed will be calculated by interpolating between the Min and Max speed.</p>
<h4>Slow down if layer print time is below</h4>
<p>If the layer print time is estimated below this number of seconds, the print move speed will be slowed down to extend the duration to this value. The slowing is done by scaling the print speeds, so some moves will still be faster than others.</p>
<h4>Min print speed</h4>
<p>The minimum speed that PrusaSlicer will scale the speeds down to. Printing at extremely low speeds for extended periods of time could lead to problems such as heat creep.</p>
<p>Keep in mind that by raising this value too high, you may partially invalidate the minimum layer time set by <strong>Slow down if layer print time is below</strong>. Because even when printing at this minimum speed, the layer time might be shorter than the set value.</p>


Cooling

Original Prusa Curing and Washing Machine (CW1S) is a recommended accessory for the Original Prusa SL1S

Original Prusa CW1 to CW1S platform upgrade

Upgrade platformy Original Prusa CW1 na CW1S

Original Prusa CW1 zu CW1S Plattform Upgrade

Mejora de la plataforma Original Prusa CW1 a CW1S

Mise à niveau de la plateforme de l'Original Prusa CW1 vers la CW1S

Aggiornamento piattaforma da Original Prusa CW1 a CW1S

Original Prusa CW1 to CW1S platform upgrade [進行中の翻訳]

Aktualizacja platformy Original Prusa CW1 do CW1S

Original Prusa i3 MK3/MK3S/MK3S+ to MK3.9 upgrade

Upgrade tiskárny Original Prusa i3 MK3/MK3S/MK3S+ na MK3.9

Original Prusa i3 MK3/MK3S/MK3S+ auf MK3.9 Upgrade

Actualización de Original Prusa i3 MK3/MK3S/MK3S+ a MK3.9

Mise à niveau de l'Original Prusa i3 MK3/MK3S/MK3S+ vers la MK3.9

Original Prusa MK3.9 [進行中の翻訳]

Modernizacja Original Prusa i3 MK3/MK3S/MK3S+ do MK3.9

Original Prusa i3 MK3/MK3S/MK3S+ to MK4 upgrade

Upgrade z Original Prusa i3 MK3/MK3S/MK3S+ na MK4

Original Prusa i3 MK3/MK3S/MK3S+ auf MK4 Upgrade

Actualización Original Prusa i3 MK3/MK3S/MK3S+ a MK4

Mise à niveau de l'Original Prusa i3 MK3/MK3S/MK3S+ vers la MK4

Aggiornamento da Original Prusa i3 MK3/MK3S/MK3S+ a MK4

Original Prusa i3 MK3/MK3S/MK3S+ to MK4 upgrade [進行中の翻訳]

Modernizacja Original Prusa i3 MK3/MK3S/MK3S+ do MK4

Original Prusa i3 MK3/MK3S/MK3S+ to MK4S/MK3.9S upgrade

Upgrade z Original Prusa i3 MK3/MK3S/MK3S+ na MK4S

Original Prusa i3 MK3/MK3S/MK3S+ auf MK4S/MK3.9S Upgrade

Original Prusa i3 MK3/MK3S/MK3S+ to MK4S upgrade [Traducción en desarrollo]

Mise à niveau d'Original Prusa i3 MK3/MK3S/MK3S+ vers la MK4S/MK3.9S

Aggiornamento da Original Prusa i3 MK3/MK3S/MK3S+ a MK4S/MK3.9S

Original Prusa i3 MK3/MK3S/MK3S+ to MK4S upgrade [進行中の翻訳]

Modernizacja Original Prusa i3 MK3/MK3S/MK3S do MK4S/MK3.9S

Original Prusa i3 MK3S/MK3S+ to MK3.5 upgrade

Upgrade tiskárny Original Prusa i3 MK3S/MK3S+ na MK3.5

Original Prusa i3 MK3S/MK3S+ auf MK3.5 Upgrade

Actualización de Original Prusa i3 MK3S/MK3S+ a MK3.5

Mise à niveau de l'Original Prusa i3 MK3S/MK3S+ vers la MK3.5

Aggiornamento da Original Prusa i3 MK3S/MK3S+ a MK3.5

Original Prusa i3 MK3S/MK3S+ to MK3.5 upgrade [進行中の翻訳]

Modernizacja Original Prusa i3 MK3S/MK3S+ do MK3.5

Original Prusa i3 MK3S/MK3S+ to MK3.5S upgrade

Upgrade z Original Prusa i3 MK3S/MK3S+ na MK3.5S

Original Prusa i3 MK3S/MK3S+ auf MK3.5S Upgrade

Actualización de Original Prusa i3 MK3S/MK3S+ a MK3.5S

Mise à niveau de l'Original Prusa i3 MK3S/MK3S+ vers la MK3.5S

Aggiornamento da Original Prusa i3 MK3S/MK3S+ a MK3.5S

Original Prusa MK4 to MK4S upgrade [進行中の翻訳]

Modernizacja Original Prusa i3 MK3S/MK3S do MK3.5S

Original Prusa MK4 kit assembly

Sestavení stavebnice Original Prusa MK4

Kit de montaje Original Prusa MK4

Assemblage du kit de l'Original Prusa MK4

Original Prusa MK4 kit di assemblaggio

Original Prusa MK4 キットの組み立て

Montaż zestawu Original Prusa MK4

Original Prusa MK4/MK3.9 to MK4S/MK3.9S upgrade

Upgrade z Original Prusa MK4/MK3.9 na MK4S/MK3.9S

Original Prusa MK4/MK3.9 auf MK4S/MK3.9S Upgrade

Actualización de Original Prusa i3 MK4/MK3.9 a MK4S/MK3.9S

Mise à niveau de l'Original Prusa MK4/MK3.9 vers la MK4S/MK3.9S

Aggiornamento da Original Prusa MK4/MK3.9 a MK4S/MK3.9S

Modernizacja Original Prusa MK4/MK3.9 do MK4S/MK3.9S

Original Prusa MK4S kit assembly

Sestavení stavebnice Original Prusa MK4S

Original Prusa MK4S kit assembly [Traducción en desarrollo]

Assemblage du kit de l'Original Prusa MK4S

Original Prusa MK4S kit di assemblaggio

Original Prusa MK4S kit assembly [進行中の翻訳]

Montaż zestawu Original Prusa MK4S

Original Prusa Enclosure assembly

Sestavení stavebnice Original Prusa Enclosure (NOVÝ)

Original Prusa Enclosure Montage

Montaje del Original Prusa Enclosure

Assemblage de l'Original Prusa Enclosure

Assemblaggio Original Prusa Enclosure

Original Prusa Enclosure assembly (NEW) [進行中の翻訳]

Montaż Original Prusa Enclosure

The Original Prusa i3 MK3S+ is the successor of the award-winning Original Prusa i3 MK2S 3D printer.

Original Prusa i3 MK3S+ kit assembly

Sestavení stavebnice Original Prusa i3 MK3S+

Original Prusa i3 MK3S+ Bausatz

Montaje del kit Original Prusa i3 MK3S+

Kit de l'Original Prusa i3 MK3S+

Montaggio kit Original Prusa i3 MK3S+

Original Prusa i3 MK3S+ キットアセンブリ

Montaż zestawu Original Prusa i3 MK3S+

Original Prusa MMU3 Assembly

Sestavení Original Prusa MMU3

Original Prusa MMU3 Bausatz

Ensamblaje Original Prusa MMU3

Assemblage de l'Original Prusa MMU3

Assemblaggio Original Prusa MMU3

Original Prusa MMU3 キット組立て

Montaż Original Prusa MMU3

Original Prusa Enclosure assembly (external display mounting)

Sestavení stavebnice Original Prusa Enclosure

Original Prusa Enclosure Montage (externe Display-Befestigung)

Montaje del Original Prusa Enclosure (montaje externo de la pantalla)

Assemblage de l'Original Prusa Enclosure (montage de l'écran externe)

Assemblaggio Original Prusa Enclosure (montaggio esterno del display)

Original Prusa Enclosure [進行中の翻訳]

Montaż Original Prusa Enclosure (wyświetlacz na zewnątrz)

Original Prusa MK4S with MMU3 (assembled)

Original Prusa MK4S s MMU3 (složená)

Original Prusa MK4S mit MMU3 (montiert)

Original Prusa MK4S with MMU3 (assembled) [Traducción en desarrollo]

Original Prusa MK4S avec MMU3 (assemblé)

Original Prusa MK4S con MMU3 (assemblata)

Original Prusa MK4S with MMU3 (assembled) [進行中の翻訳]

Original Prusa MK4S z MMU3 (zmontowane)

Original Prusa SL1 to SL1S SPEED upgrade

Upgrade tiskárny Original Prusa SL1 na SL1S SPEED

Original Prusa SL1 aus SL1S SPEED Upgrade

Mejora Original Prusa SL1 a SL1S SPEED

Mise à niveau de l'Original Prusa SL1 vers la SL1S SPEED

Aggiornamento da Original Prusa SL1 a SL1S SPEED

Růženka Upgrade Final [進行中の翻訳]

Aktualizacja Original Prusa SL1 do SL1S SPEED

Original Prusa XL Single-Tool (Assembled)

Original Prusa XL Single-Tool (Sestavená)

Original Prusa XL Einzel-Kopf (montiert)

Original Prusa XL Mono Cabezal (Ensamblada)

Original Prusa XL Mono-outil (Assemblée)

Disimballaggio Original Prusa XL a strumento singolo (Assemblata)

Original Prusa XL [進行中の翻訳]

Original Prusa XL 1-głowicowa (zmontowana)

Original Prusa MINI+ kit assembly

Sestavení stavebnice Original Prusa MINI+

Original Prusa MINI+ Kit Montage

Montaje Kit Original Prusa MINI+

Assemblage du kit Original Prusa MINI+

Assemblaggio kit Original Prusa MINI+

MINI+ kit assembly (draft) [進行中の翻訳]

Montaż zestawu Original Prusa MINI+

Original Prusa MK3S+ MMU3 to MK4/MK3.9 MMU3 upgrade

Upgrade tiskárny Original Prusa MK3S+ MMU3 na MK4/MK3.9 MMU3

Original Prusa MK3S+ MMU3 auf MK4/MK3.9 MMU3 Upgrade

Actualización de Original Prusa MK3S+ MMU3 a MK4/MK3.9 MMU3

Mise à niveau du MMU3 de l'Original Prusa MK3S+ vers le MMU3 de la MK4/MK3.9

Aggiornamento da Original Prusa MK3S+ MMU3 a MK4/MK3.9 MMU3

Original Prusa MK3S+ MMU3 upgrade kit to MK4/MK3.9 Assembly [進行中の翻訳]

Modernizacja Original Prusa MK3S+ MMU3 do MK4/MK3.9 MMU3

Original Prusa XL Single-Tool (Semi-Assembled)

Original Prusa XL Single-Tool (Částečně sestavená)

Original Prusa XL Einzel-Kopf (teilmontiert)

Original Prusa XL Mono Cabezal (Semi-Ensamblada)

Original Prusa XL Mono-outil (Semi-Assemblée)

Original Prusa XL a strumento singolo (Semi-assemblata)

Original Prusa XL semi-kit assembly INTERNAL [進行中の翻訳]

Original Prusa XL 1-głowicowa (wstępnie zmontowana)

Original Prusa i3 to MMU2S upgrade

Upgrade z Original Prusa i3 na MMU2S

Original Prusa i3 auf MMU2S Upgrade

Actualización de Original Prusa i3 a MMU2S

Mise à niveau Original Prusa i3 vers MMU2S

Aggiornamento Original Prusa i3 ad MMU2S

Original Prusa i3 MK3S to MMU2S [進行中の翻訳]

Aktualizacja Original Prusa i3 do MMU2S

Original Prusa XL Dual-Head (Assembled)

Original Prusa XL Dual-Head (Sestavená)

Original Prusa XL Dual-Kopf (montiert)

Original Prusa XL Doble Cabezal (Ensamblada)

Original Prusa XL Double-tête (Assemblée)

Disimballaggio Original Prusa XL a due strumenti (Assemblata)

Original Prusa XL unpacking (double tool) [進行中の翻訳]

Original Prusa XL 2-głowicowa (zmontowana)

Original Prusa i3 MK3/MK3S to MK3S+ upgrade

Upgrade z Original Prusa i3 MK3/MK3S na MK3S+

Original Prusa i3 MK3/MK3S auf MK3S+ Upgrade

Actualización de Original Prusa i3 MK3/MK3S a MK3S+

Mise à niveau de l'Original Prusa i3 MK3/MK3S vers la MK3S+

Aggiornamento da Original Prusa i3 MK3/MK3S a MK3S+

Original Prusa i3 MK3 to MK3S+ upgrade [進行中の翻訳]

Aktualizacja Original Prusa i3 MK3/MK3S do MK3S+

The Original Prusa MINI+ is a compact 3D printer with all the bells and whistles you would expect from the creators of the award-winning Original Prusa i3 MK2 and MK3S!

Original Prusa MINI+ semi-assembled

Sestavená tiskárna Original Prusa MINI+

Original Prusa MINI+ halbmontiert

Original Prusa MINI+ semi-montada

Original Prusa MINI+ semi-assemblée

Original Prusa MINI+ semi-assemblata

Original Prusa MINI+ 半組立済み

Częściowo zmontowana Original Prusa MINI+

Original Prusa XL Dual-Head (Semi-Assembled)

Original Prusa XL Dual-Head (Částečně sestavená)

Original Prusa XL Dual-Kopf (teilmontiert)

Original Prusa XL Doble Cabezal (Semi-Ensamblada)

Original Prusa XL Double-tête (Semi-Assemblée)

Original Prusa XL doppio strumento (Semi-Assemblata)

Original Prusa XL semi-assembled (Dual-Head) [進行中の翻訳]

Original Prusa XL 2-głowicowa (wstępnie zmontowana)

Original Prusa SL1 3D printer is based on the MSLA printing process. Unlike Original Prusa i3 machines, this printer uses a high-resolution LCD panel and a UV LED to cure thin layers of resin to achieve an unprecedented level of detail.

Original Prusa SL1 kit assembly

Sestavení stavebnice Original Prusa SL1

Assembly manuals

Filament settings

All articles

Max volumetric speed

Cooling

Still have questions?