⬢Needle-nose pliers
⬢2.5mm Allen key
FR
Se Connecter- English
- Čeština
- Español
- Italiano
- Deutsch
- Polski
- Home
- MK2S
- Manuels d'assemblage
- Assemblage du kit Original Prusa i3 MK2S
- 6. Assemblage du LCD
6. Assemblage du LCD
Menu
- Assemblage du kit Original Prusa i3 MK2S
- 1.Introduction
- 2. Y-axis assembly
- 3. Assemblage de l’axe X
- 4. Assemblage de l’axe Z
- 5. Assemblage de l'Extrudeur
- 6. Assemblage du LCD
- 1. Get the necessary tools
- 2. 3D printed parts
- 3. Preparing the LCD support for assembly
- 4. Adjusting the LCD-support
- 5. Assembling the LCD-cover
- 6. Securing the LCD controller
- 7. Assembling the LCD knob
- 8. Plug in the cables
- 9. Secure the LCD display onto the printer
- 10. Secure the LCD assembly
- 11. Guiding the LCD cables
- 12. All done!
- 7. Assemblage de l'alimentation et du lit chauffant
- 8. Assemblage de l'électronique
- 9. Contrôle avant lancement
6. Assemblage du LCD
Pertinent pour:
Dernière mise à jour 5 years ago Difficulté
Modéré Étapes
12 Langues disponibles
⬢LCD-cover
⬢LCD-knob
⬢LCD-support
⬢LCD-cable-clip
⬢Prepare the LCD controller and LCD-support printed parts as shown in the picture.
Ensure the correct orientation of parts and the LCD controller.
⬢Slide the LCD-support parts on the LCD-controller.
The exact position will be adjusted in the next step, no need to worry at this moment.
You can now remove the protective foil from the LCD panel.
Cables to LCD are factory installed, but you can disconnect them.
⬢Adjust the LCD-support parts as shown in the picture.
⬢LCD-support parts must face directly into the cutouts in the LCD-cover.
⬢Press the LCD controller with the LCD-support into the LCD-cover as shown in the picture.
⬢Press it as deep as possible.
⬢The LCD controller must click under support in the center of the LCD-cover.
⬢M3x10 screws (2 pcs)
⬢Using the 2.5mm allen key, secure the LCD controller in place.
⬢Assemble the LCD-knob part as shown in the picture.
⬢Plug in the cables as shown in the picture.
⬢Cable with 1 stripe has to be plugged in the connector labeled with EXP1.
⬢Cable with 2 stripes has to be plugged in the connector labeled with EXP2.
⬢Press the LCD assembly onto the front side of the Y-axis.
Best way is to press the LCD assembly on the top threaded rod first and then on the bottom.
⬢Guide the LCD cables in between threaded rods as in the picture.
⬢Use the zipties to anchor the LCD assembly to the threaded rods.
⬢Guide the LCD cables using LCD-clips as seen in the picture.
⬢Reverse direction of each of the clip, to prevent side movement of the cables.
⬢Congratulations! You've attached the LCD to the Prusa i3 3D printer!
⬢You can continue by assembling the PSU and the heatbed in the next chapter - 7. Assemblage de l'alimentation et du lit chauffant.
Ce guide vous a-t-il été utile ?
Commentaires
Vous avez encore des questions ?
Si vous avez une question sur un sujet qui n'est pas traité ici, consultez nos ressources supplémentaires.
Et si cela ne suffit pas, vous pouvez envoyer une demande à [email protected] ou via le bouton ci-dessous.