⬢For this step please use the shorter one and DON'T TRIM it!

⬢Using the pliers cut one end of the filament to create a tip.

⬢Check the tip is similar to the third picture.

⬢Insert M3n nuts in the printed part.

⬢In case you can't press the M3n nut in, don't use excessive force. Take the M3 bolt and thread it from the opposite side of the printed part, as you tighten the screw, it will pull the nut in. Be careful not the break the printed part during tightening.

⬢Place the heatbed-cable-cover on the heatbed to cover the soldered cables and LED.

⬢Tighten the cover to the heatbed using M3x10 screw and Allen key. Be careful not to pinch (break) any wires from the heatbed!

⬢Guide the black thermistor cable next to the heatbed heater cable and wrap it few times around (see the photo).

The thermistor cable is in black or white colour, their functionality is the same.

⬢Use the spiral wrap and wrap the cables from the heatbed including the NYLON. Start by one or two wraps 1 cm behind the heatbed cover.

⬢When the first wrap is ready, slide it inside the heatbed cover. Ensure it is at least 5-6 mm.

⬢Continue with wrapping the spiral wrap.

DO NOT cut the filament, you'll need the full length.

⬢Place second part of the cover on the top of the spiral wrap.

⬢Insert two screws M3x10 and tighten them, proceed with caution and tighten both screws equally.

⬢Your tightened cover should look like the last picture.

⬢Ready? Jump to Step 19

⬢For this step please use the shorter one and DON'T TRIM it!

⬢Using the pliers cut one end of the filament to create a tip.

⬢Check the tip is similar to the third picture.

⬢Place the heatbed-cable-cover on the heatbed to cover the soldered cables and LED.

⬢Tighten the cover to the heatbed using M3x10 screw and Allen key. Be careful not to pinch (break) any wires from the heatbed!

The thermistor cable is in black or white colour, their functionality is the same.

⬢Guide the black thermistor cable next to the heatbed heater cable and wrap it few times around (see the photo).

⬢Use the spiral wrap and wrap the cables from the heatbed including the NYLON. Start by one or two wraps 1 cm behind the heatbed cover.

⬢When the first wrap is ready, slide it inside the heatbed cover.

⬢Continue with wrapping the spiral wrap.

DO NOT cut the filament, you'll need the full length.

⬢Place a zip tie around the heatbed cover to tighten the spiral wrap with cables. There is a channel around the cover designed for the zip tie.

⬢Cut the remaining part of the zip tie.

⬢Push the Y-carriage to the front and place the Heatbed behind.

⬢Locate a hole the centre of the Y-carriage.

⬢Place one spacer on the top of the hole.

The exact position of the spacer will be adjusted in the next step.

⬢Push the Allen key through the middle hole on the Heatbed and place it above the spacer. Use the Allen key to align all parts.

⬢After the alignment insert the M3x12b(14b) screw instead.

⬢Tighten the screw just slightly.

⬢Move to the right side of the heatbed.

⬢Place another spacer with the pliers.

⬢Push the pliers between the heatbed and the Y-carriage.

⬢Use the Allen key to align the spacer.

⬢After the alignment insert the screw instead and tighten it slightly.

⬢Using pliers insert spacers and screw into the remaining holes. DON'T fully tighten the screws.

⬢After all screws are in place, tighten them in the following order:

⬢Center screw

⬢First four screws

⬢Last four screws

⬢Locate four mounting points on the YZ frame.

⬢Place the PSU on the frame and secure it with the M4x10r screws. Don't tighten them completely.

⬢Slide the PSU holders under the PSU cover.

⬢Secure the PSU with two M3x10 screws. Don't tighten them completely. You want to be able to move the PSU on the mount to properly line up the other mount.

⬢Re-seat the PSU and then tighten all four screws.