Tools are not included in the add-on package.

⬢2.5mm Allen key

⬢Needle-nose or cutting pliers

⬢Phillips screwdriver PH2

⬢Carefully cut the zip tie securing the LCD cable bundle.

⬢Release two screws mounting the LCD assembly.

⬢Disconnect both LCD cables from the LCD.

⬢Push the LCD cable bundle through the hole in the bottom panel into the enclosure.

⬢Open the door of the enclosure.

⬢Place the printer at an angle (as shown in the picture) in the enclosure behind the anti-slip dampers.

⬢"Unlock" all PSU-locks and grasp the PSU assembly by its handle and remove it from the back panel.

⬢Place the PSU on the heatbed protected with the cloth. Turn it with the PSU-handle facing upwards.

⬢On the PSU holder, cut off the zip tie securing the PSU cable.

⬢On the other side of the PSU assembly, loosen two screws mounting the PSU-cover and remove the cover from the PSU.

⬢Using a Phillips screwdriver, loosen all the screws on the PSU cables. No need to remove the screws.

⬢Remove all PSU cables from the terminals.

⬢PSUからパワーパニックケーブルを外します。

⬢Place the disconnected PSU aside for now. We'll come back to that later.

⬢Cut off the zip tie merging both cable bundles.

⬢From the back of the Einsy case, loosen the screw to open the door of the electronic box.

⬢Using the Phillips screwdriver, loosen the screws securing the PSU cables (the first four from the left). And remove all the cables from the terminals.

⬢Disconnect the Power panic cable from the electronics board.

⬢Keep the electronics box open.

⬢Remove the plug from the PSU holder.

⬢Insert the Quick Release cable - Black PSU Side into the hole in the PSU holder.

⬢From the opposite side of the PSU holder check that the latches on the connector are engaged with the metal sheet.

⬢Take the first positive (red) wire from the Quick Release cable - Black PSU Side connector and connect it to the first terminal from the left on the PSU. Bent part of the connector is facing up. Push it below the square washer, all the way in.

⬢Connect the power panic cable to the PSU.

⬢Connect the power panic cable to the Einsy board.

⬢Guide the power panic cable according to the picture.

⬢Arrange all cables as you can see in the picture.

⬢Close the electronics box and tighten the M3x40 screw.

⬢Textile sleeve 8 x 350 mm (1x) you removed earlier

⬢Zip tie (3x)

⬢From the electronics, wrap the quick release cable (including the black&white power panic cable) in the textile sleeve.

⬢Leave 2-5 cm from the electronics uncovered. Secure the end of the sleeve with the zip tie.

⬢Merge the LCD cable bundle and the PSU cable bundle and secure them together with the zip tie.

⬢Now, prepare the enclosure on the work surface.

⬢Ensure the PSU-locks are still turned at the same position:

⬢Push the PSU through the opening in the back panel.

⬢Attach the PSU-holder on the all PSU-locks.

⬢Turn all PSU-lock 90° to lock the PSU assembly.

⬢Grasp the quick release guiding from the printer, with the power panic cable on the left.

⬢Plug the connector to the quick release cable in the PSU holder.

⬢Rearrange position of the printer like in the picture. Place it in the center of the enclosure and adjust the correct position.

⬢LCD assembly (1x)

⬢Thumb screw M3x8 (2x)

⬢Guide the LCD cable through the cutout in the bottom panel.

⬢Secure the textile sleeve on the cable bundle with the zip tie. Do not over tighten the zip tie, it may cut the cables!

⬢From the inside, push two thumb screws M3x8 through the bottom profile.

⬢Place the LCD assembly close to the LCD cables, like in the picture. Mind the same orientation of the LCD as in the picture. See the LCD-supports for better understanding.

⬢Slide the LCD assembly onto the two M3x8 screws in the frame and tighten them.