LCD menu (XL Multi Tool) | Prusa Knowledge Base

The Original Prusa XL is equipped with a color LCD screen that, among other things, supports G-code thumbnails and QR codes.

For the versions of the XL printer with a single tool head, go to LCD menu (XL Single Tool).

The footer of the main screen can be edited to show the features you wish to be shown on the main page.

If you have a Dual Toolhead printer, only two tools will appear in the menu shown below.

Make sure to always have the latest latest firmware.

Menu structure

Print
Preheat
- - PLA
  - PETG
  - ASA
  - PC
  - PVB
  - ABS
  - HIPS
  - PP
  - FLEX
  - PA
  - Cooldown
Filament
- - Load filament
  - Unload filament
  - Change filament
  - Purge filament
  - Change Filament in All Tools
    - - Tool 1 Filament
      - Tool 2 Filament
      - Tool 3 Filament
      - Tool 4 Filament
      - Tool 5 Filament
      - Carry Out the Changes
Control
- - Pick/Park Tool
    - - Park Current Tool
      - Pick Tool 1
      - Pick Tool 2
      - Pick Tool 3
      - Pick Tool 4
      - Pick Tool 5
  - Move axis
    - - Move X
      - Move Y
      - Move Z
      - Move E
      - Cooldown
  - Temperature
    - - Nozzle 1 temperature
      - Nozzle 2 temperature
      - Nozzle 3 temperature
      - Nozzle 4 temperature
      - Nozzle 5 temperature
      - Heatbed temperature
      - Print fan speed
      - Cooldown
  - Autohome
  - Set ready
  - Disable motors
  - Enclosure
  - Cold Pull
  - Calibrations & Tests
    - - 1 Fan Test
      - 2 Y Axis Test
      - 3 X Axis Test
      - 4 Z Alignment Calibration
      - 5 Dock Position Calibration
      - 6 Loadcell Test
      - 7 Z Axis Test
      - 8 Nozzle Heaters Test
      - 9 Filament Sensor Calibration
      - 10 Tool Offset Calibration
      - 11 Bed Heater Test
      - 12 Phase Stepping Calibration
Settings
- - Filament Sensors
    - - Filament Sensing
      - Side Filament Sensor 1
      - Side Filament Sensor 2
      - Side Filament Sensor 3
      - Side Filament Sensor 4
      - Side Filament Sensor 5
      - Toolhead Filament Sensor 1
      - Toolhead Filament Sensor 2
      - Toolhead Filament Sensor 3
      - Toolhead Filament Sensor 4
      - Toolhead Filament Sensor 5
      - Restore Defaults
  - Stuck Filament Detection
  - Stealth Mode
  - Fan check
  - Verify Gcode
  - Crash Detection
  - Tools
    - - Tool 1
        
        Nozzle Diameter
        
        Dock X
        
        Dock Y
        
        Calibrate Dock Position
        
        Calibrate Filament Sensor
        
        Pickup Tool
      - Tool 2
      - Tool 3
      - Tool 4
      - Tool 5
      - Park Current Tool
  - Input Shaper
    - - X-axis filter
      - X-axis frequency
      - Y-axis filter
      - Y-axis frequency
      - Restore Defaults
  - User Interface
    - - Footer
      - Sort Files [Time/Name]
      - Print Progress Screen [OFF, 30 s - 200 s]
      - Menu Timeout
      - Sound Mode [Loud/Silent/Assist/Once]
      - For filament change, preheat [Nozzle/Noz&Bed]
      - RGB Status Bar
      - RGB Side Strip
      - RGB Side Strip Dimming
      - Tool Light
      - Touch
      - Touch Sig Workaround
  - Language & Time
    - - Language
        
        English
        
        Čeština
        
        Deutsch
        
        Español
        
        Français
        
        Italiano
        
        Polski
        
        ニホンゴ
      - Time Zone Hour Offset
      - Time Zone Minute Offset
      - Time Zone Summertime
      - Time Format
  - Network
    - - Active Interface [Eth/Wi-fi]
      - Network status
        
        IPv4 Address
        
        IPv4 Gateway
        
        MAC Address
        
        Hostname
        
        DNS Server
        
        Ping | Loss
        
        Gateway
        
        DNS server
      - Wi-Fi
        
        Wi-Fi status
        
        SSID
        
        Wi-Fi Wizard
        
        Protocol
        
        LAN
        
        IPv4 Address
        
        IPv4 Netmask
        
        IPv4 Gateway
        
        Hostname
        
        MAC Address
      - Ethernet
        
        Protocol
        
        LAN
        
        IPv4 Address
        
        IPv4 Netmask
        
        IPv4 Gateway
        
        Hostname
        
        MAC Address
      - Prusa Connect
        
        Enabled
        
        Status
        
        Error
        
        Hostname
        
        Add printer to Connect
        
        Load Settings
      - Prusa Link
        
        Enabled
        
        User
        
        Password
        
        IPv4 address
        
        Hostname
        
        Generate Password
      - Metrics & Log
        
        What is this?
        
        Allow
        
        Enable Stored on Startup
        
        Stored configuration
        
        Host
        
        Metrics port
        
        Log Port
        
        Current configuration
        
        Metrics Host
        
        Metrics Port
        
        Log Host
        
        Log Port
  - Hardware
    - - G-code checks
        
        Nozzle Diameter [Warn/Strict/None]
        
        Printer Model [Warn/Strict/None]
        
        Firmware Version [Warn/Strict/None]
        
        G-code Level [Warn/Strict/None]
      - Side FSensor Remap
      - Heat Entire Bed
      - Crash Sensitivity XY
      - Phase Stepping
  - FW update
  - System
    - - Save Crash Dump
      - Device Hash in QR
      - Load Settings from File
      - Factory Reset
        
        Reset Settings & Calibrations
        
        Hard Reset (USB with FW needed)
Info
- - Network info
  - Sensor Info
    - - Heatbreak 1Temp
      - Heatbreak 2 Temp
      - Heatbreak 3 Temp
      - Heatbreak 4 Temp
      - Heatbreak 5 Temp
      - Board Temperature
      - MCU Temperature
      - Bed Temperature
      - Nozzle 1 Temperature
      - Nozzle 2 Temperature
      - Nozzle 3 Temperature
      - Nozzle 4 Temperature
      - Nozzle 5 Temperature
      - Dwarf Board Temp
      - Dwarf MCU Temp
      - MBed MCU Temp
      - Loadcell Value
      - Tool Filament Sensor
      - Side Filament Sensor
      - Print Fan
      - Heatbreak Fan
      - Input Voltage
      - 5V Voltage
      - Sandwich 5V Current
      - XL Buddy 5V Current
  - Version info
    - - Firmware Version
      - Bootloader Version
      - Buddy Board
      - Serial Number
      - xLCD
  - Print Statistics
    - - Fail Stats
        
        Power Failures
        
        Last Print Crashes on X Axis
        
        Last Print Crashes on Y Axis
        
        Crashes on X Axis
        
        Crashes on Y Axis
      - Statistics
        
        X-axis
        
        Y-axis
        
        Z -axis
        
        Filament
        
        Tool 1
        
        Tool 2
        
        Tool 3
        
        Tool 4
        
        Tool 5
        
        Tools changed
        
        Tool 1
        
        Tool 2
        
        Tool 3
        
        Tool 4
        
        Tool 5
      - Print Time

1 comment

XL beta tester for far too long

•

10 months ago

Explanation for some of the uncommon settings would be nice.