⬢For this chapter, please prepare:
⬢T10 Torx key
⬢2.5 mm Allen key
⬢4.0 mm Allen key
⬢A cardboard box is to be used as heatbed protection during the setup. Hint: you can use the Nextruder box shipped with your printer.
JA
Login- English
- Čeština
- Español
- Italiano
- Deutsch
- Polski
- Français
- Home
- XL
- 組立てガイド
- Original Prusa XL Five-Head (Semi-Assembled) [進行中の翻訳]
- 5. Tool-changer assembly
5. Tool-changer assembly
Menu
- Original Prusa XL Five-Head (Semi-Assembled) [進行中の翻訳]
- 1. Introduction
- 2. ベースとサイドフレームの組み立て
- 3. CoreXY & Back assembly
- 4. Heatbed & Side panels assembly
- 5. Tool-changer assembly
- 1. Tools necessary for this chapter
- 2. Preparing the X-carriage
- 3. Installing the ToolChanger: parts preparation
- 4. Preparing the ToolChanger
- 5. Installing the ToolChanger
- 6. Covering the X-carriage
- 7. Almost done
- 6. Extruder & accessories assembly
- 7. First run
- Manual changelog Five-Head (Semi-Assembled)
5. Tool-changer assembly
Relevant for:
Last updated 10 months ago Difficulty
Very easy Steps
7 Available languages
Reminder: To handle the printer, always grab the handles on both sides of the printer. Do not lift the printer by the aluminum extrusions or the metal sheet profiles on top.
In the following steps, we will work with tools and install the Nextruder above the heatbed, it is recommended to protect it against any possible damage. An empty Prusament box can serve this purpouse.
⬢For better access when mounting the Nextruder, manually move the heatbed down.
⬢Place the empty cardboard box approximately to the front center part of the heatbed.
⬢Move the X-axis assembly all the way to the front side of the printer.
⬢Move the X-carriage approximately to the center of the X-axis.
⬢For the following steps, please prepare:
⬢Tool Changer Upper Lock (1x)
⬢Tool Changer Lower Lock (1x)
⬢Spring 3x9 (4x)
⬢TC push pin (4x)
⬢M3x12cT screw (4x)
⬢X-carriage-cover (1x)
⬢Insert each TC push pin into the holes in both metal parts.
⬢Insert each spring 3x9 into the same holes as a TC push pins.
⬢The tool changer is prepared. The springs must be sticking out.
Be careful that the springs and pins do not fall out when handling the parts.
Be careful that the springs and pins do not fall out when handling the parts.
⬢Line up the screws in the TC block lower assembly lock with the blind holes in the X-carriage. See the correct orientation of the part. Use the U-shaped groove in the part.
⬢Take a look at the X-carriage from the rear side.
⬢Attach the TC block lower assembly lock to the X-carriage and secure it with two M3x12cT screws from the front side. Ensure the correct orientation of the part.
⬢Attach the TC block upper assembly to the X-carriage from the top and secure it with two M3x12cT screws from the front side.
⬢Attach the x-carriage-cover on the X-carriage with the hole up.
⬢Push the center of the cover using your thumb. The cover will then snap into the latches on the X-carriage. You will feel a light "click" when it is successfully snapping.
⬢That wasn't so hard. Anyway, good job!
⬢Now go to the next chapter 6. Extruder & accessories assembly
Was this guide helpful?
Comments
Still have questions?
If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.