⬢キットにはデフォルトでは同梱されていませんが、プリントアウトして組み立て時にエンクロージャーに追加することができます。締結部品類はすでにキットに含まれています。

⬢To see the full list of the parts, please visit our collection at Printables.com.

⬢Grasp the Spool-holder-r and turn clockwise to unlock it and remove it from the MINI Enclosure.

⬢Pull the power cord handle towards you to release and disconnect the power cord from the back of the printer.

⬢If necessary, disconnect an ethernet cable.

⬢Disconnect the USB extension cable from the right side of the printer.

⬢From the front side of the MINI Enclosure:

⬢Move the heatbed towards you.

⬢Carefully take the printer.

⬢Carefully pull the printer out of the MINI Enclosure with the base facing backwards. Be EXTRA CAREFUL when doing this:

⬢Put the printer aside.

From October 2024 you may receive two different manufacturers of the PSU, the pictures may be different but the assembly process is the same. 

⬢PSU (1x)

⬢Zip tie (6x)

⬢Slightly loosen the left screw behind the circle hole.

⬢Release and remove the right screw. Don't throw the screw away!

⬢Remove the printer PSU cable from the rear hole.

⬢Reposition the foot as shown in the picture. Keep the cable in the cable channel.

⬢Insert the PSU cable with the ferrite core through the circular hole at the rear of the Enclosure.

⬢Guide the PSU cable with the connector through the front circle hole out of the Enclosure.

⬢Insert the printer PSU cable back through the rear hole.

⬢Close the foot back to its original position and align the holes in the foot and Enclosure.

⬢After aligning the hole, secure the foot by inserting back the M3x12 screw.

⬢Fully tighten the left screw.

⬢Release and remove both M3x12 screws.

⬢Reposition the foot as shown. Push the PSU cable into the cable channel.

⬢Push the PSU cable into the cable channel.

⬢Close the foot back to its original position and align the holes.

⬢Secure the foot by inserting back the M3x12 screws and tighten them firmly.

⬢Guide the cable along the rear side of the Enclosure and secure it using three zip ties through the perforations. Do not overtighten the zip ties, you can damage the cable.

⬢Guide the PSU cable along with the FAN cable on the left side of the Enclosure and secure it with the three zip-ties. Do not overtighten the zip ties, you can damage the cables.

⬢If you have installed the Advanced Filtration System, guide the filtration cable together with the PSU cable. Secure it with one extra zip tie in the left corner. Do not overtighten the zip tie, you can damage the cables.

⬢LED Stick Board (1x)
WARNING: Make sure to protect the electronics against electrostatic discharge (ESD). Always unpack the electronics right before you need them!

⬢LED diffuser (1x)

⬢LED Stick Bracket (3x)

⬢M3x18 screw (3x)

⬢M3n nut (3x)

⬢Insert the M3n nut into each LED Stick Bracket.

⬢Slide the lower slot of the LED Stick Bracket on the LED Stick Board and align the bracket against the first hole in the LED Stick Board closest to the (white) LED stick connector.

⬢Push the LED Stick Bracket all the way on the LED Stick Board.

⬢Use this procedure for all three LED Stick Brackets.

⬢Remove the protection films from both sides of the LED diffuser.

⬢Push the LED diffuser into the LED Stick Brackets. Use the upper slot.

From now on, we will demonstrate LED mounting on the printer without the door panel for better visibility. Please note, do not remove the door panel from your printer. The printer in the pictures will be shown without door panel for improved visualization for the customers.

⬢From the inside of the enclosure, attach the LED strip assembly so that the LED stick brackets are aligned precisely with the screws. Attach the back side (the side without the diffuser).

⬢Secure the LED panel from the outside of the frame with three M3x18 screws. Tighten them firmly but gently.

⬢LED cable (1x)

⬢Zip tie (1x)

⬢Connect the LED cable to the connector on the bottom of the LED strip.

⬢Guide the zip tie through the perforation in the front left profile and secure the LED cable using the zip tie. Do not overtighten the zip-tie.

⬢Guide the LED cable through the hole in the bottom panel out of the MINI Enclosure.

⬢Basic Board Cover (1x)

⬢Basic board (1x)

⬢M3w serrated lock washer (2x)

⬢M3nS nut (2x)

⬢M3x12 screw (2x)

⬢Mount the M3nS nut on the M3x12 screw. Attach it in a few threads on the tip of the screw.

⬢Push the screw with the nut all the way into the same shape hole inside the Basic Board Cover.

⬢Remove the screw from the nut.

⬢Use the same procedure for both slots in the Basic Board Cover.

If you already have an Advanced filtration system installed, leave the filtration cable in the Basic board slot labeled FAN.

⬢Connect the LED cable to the Basic Board slot labeled LED.

⬢Place the Basic Board into the Basic Board Cover and align the holes on both parts.

⬢From the inside the Enclosure, insert two M3x12 screw through the front profile.

⬢Attach two M3w serrated lock washer on the screws.

⬢Take the Basic Board assembly and align the holes with the screws in the profile.

⬢Attach the Basic Board assembly to the screws and tighten the screws from the inside.

These steps are only for LED strip and Advanced filtration system owners only. The smaller PSU space is for those with additional PSU. Otherwise, skip to Door hinges: parts preparation

⬢PSU holder is not included in the package, you will need to print it out from Printables.com

⬢XP PSU: This PSU is larger than the Delta PSU. You will need the PSU-holder-XP.

⬢Delta PSU: This PSU is smaller than the XP PSU. You will need the PSU-holder-Delta.

These steps are only for LED strip and Advanced filtration system owners only. The smaller PSU space is for those with additional Delta PSU. Otherwise, skip to 
Installing the printer

⬢次のステップのために、次のものをご用意ください：。

⬢PSU-holder (1x) this part is not included in the package, you will need to print it out from Printables.com

⬢Add-on PSU-holder-A (1x) this part is not included in the package, you will need to print it out from Printables.com

⬢Add-on PSU-holder-B (1x) this part is not included in the package, you will need to print it out from Printables.com

⬢M3x8 screw (2x)

⬢M3n nut (2x)

⬢Zip-tie (1x)

⬢Insert the M3n nut into the PSU-holder.

⬢Insert the M3n nut into the PSU-holder.

These steps are only for LED strip and Advanced filtration system owners only. The smaller PSU space is for those with additional Delta PSU.

⬢Attach the Add-on PSU-holder-A to the rails on the PSU-holder.

⬢Attach the Add-on PSU-holder-B to the rails on the PSU-holder.

⬢Remove the nylon rivet on the left bottom corner.

⬢From the inside of the enclosure, insert two M3x8 screws through the cut-outs.

⬢Attach the PSU-holder on the screws.

⬢Secure the screws from the inside.

⬢Insert the printer PSU into the PSU-holder.

⬢Insert the add-on PSU into the PSU-holder.

⬢Secure the cables together with a zip-tie.

⬢Carefully insert the printer inside the enclosure with its base facing forward. When doing so, be EXTRA CAREFUL to:

⬢Carefully place the printer on its feet. We will adjust the exact position later on.

⬢From the back of the printer, connect the PSU power cable. See the correct orientation of the cable.

⬢If necessary, connect an ethernet cable, which is optional.

⬢Connect the USB extension cable from the right side of the printer.

⬢Insert the side arm into the Spool-holder-r and turn counter-clockwise to lock it.