PL
  • English
  • Deutsch
Login

How to reverse the door orientation (CORE One)

Menu

How to reverse the door orientation (CORE One)

How to reverse the door orientation (CORE One)
Dotyczy:
CORE One
Ostatnia aktualizacja 5 hours ago
How to reverse the door orientation (CORE One)
 Poziom trudności
Łatwy
 Kroki
10
 Dostępne języki
ENDE

Krok 1 Introduction

Introduction
Introduction
⬢This guide will walk you through the steps to reverse the door orientation on the Prusa CORE One.
By default, the door on the Prusa CORE One is configured as left-hand.
Handle the parts carefully to avoid any damage to the door or printer components.

Krok 3 Demontaż panelu drzwi

Demontaż panelu drzwi
Demontaż panelu drzwi
Demontaż panelu drzwi
Demontaż panelu drzwi
⬢Open the door widely.
⬢Using the T10 Torx key, release and remove the screw securing both Door-magnets.
⬢Remove the Door-magnets (there is a magnet inside the printed part).
⬢Release and remove two screws securing the door panel in both hinges.
It is essential to hold the door panel securely while loosening the screws to prevent it from falling.
⬢Carefully slide the door panel out of the hinges.
⬢Place the door panel in a clean and safe area to avoid any damage.

Krok 4 Removing the hinges

Removing the hinges
Removing the hinges
Removing the hinges
This step will demonstrate how to remove the upper Door-hinge. The same procedure applies to the lower Door-hinge.
⬢Using the 1.5mm Allen key, push down the pin in the Door-hinge and remove it.
Make sure you don't lose the pin. We will use it later on.
⬢Unscrew the screw securing the Door-hinge.
⬢Remove the inner part of the Door-hinge.
⬢Remove the Door-hinge from the printer.
⬢Proceed the same with the lower Door-hinge.

Krok 6 Montaż magnesów drzwi

Montaż magnesów drzwi
Montaż magnesów drzwi
Montaż magnesów drzwi
Montaż magnesów drzwi
⬢Insert the Door-magnet into the upper rectangular hole in the printer frame from the inside.
⬢Ensure the part is oriented as shown in the detailed illustration.
⬢Secure the Door-magnet with the M3x4rT screw, and tighten it firmly.
⬢Proceed the same with the lower Door-magnet.

Krok 7 Zawiasy: przygotowanie części

Zawiasy: przygotowanie części
Zawiasy: przygotowanie części
Zawiasy: przygotowanie części
⬢Do kolejnych etapów przygotuj:
⬢Door-hinge-out (2x) you removed earlier
⬢Door-hinge-in (2x) you removed earlier
⬢M3x4rT screw (2x) you removed earlier
⬢Pin 2x40 (2x) you removed earlier

Krok 8 Installing the hinges

Installing the hinges
Installing the hinges
Installing the hinges
Installing the hinges
⬢Insert the Door-hinge-in into the upper rectangular hole in the printer frame from the inside.
⬢Ensure the part is oriented as shown in the detailed illustration.
⬢Secure the Door-hinge-in with the M3x4rT screw, and tighten firmly.
⬢Attach the Door-hinge-out to the Door-hinge-in.
⬢Join both parts together by carefully pushing the pin 2x40 into place.
⬢Ensure the hinge parts are properly aligned with each other before inserting the pin.
⬢Use the T8-10 Torx key to fully insert the pin until it is flush.

Krok 9 Door panel: parts preparation

Door panel: parts preparation
Door panel: parts preparation
Door panel: parts preparation
⬢Do kolejnych etapów przygotuj:
⬢Door panel (1x) you removed earlier
Handle it carefully, avoid scratching the part.
⬢M3x5rT screw (4x) you removed earlier

Krok 10 Mounting the door panel

Mounting the door panel
Mounting the door panel
Mounting the door panel
Mounting the door panel
⬢Insert the door panel fully into the hinges.
Ensure the door panel is oriented correctly, with the handle facing outward. Use the V-shaped cutouts on the inner side of the door handle as a guide.
⬢Insert two M3x5rT screws into each Door-hinge to secure the door panel.
Secure the screws gently to avoid over-tightening or damaging the door panel.
⬢The door has been successfully reversed. You can now resume normal use of the printer.
Czy ten poradnik był pomocny?

Komentarze

Wciąż masz pytania?

Wciąż masz pytania?

Jeśli masz pytanie dotyczące czegoś, czego nie opisaliśmy, to sprawdź dodatkowe zasoby.
A jeśli to nie działa, możesz wysłać zgłoszenie na [email protected] lub klikając poniższy przycisk.

Kontakt