日本語

1. 組み立てを始める

Step 1 of 27 (Chapter 31 of 39)

内容

How to change xLCD and xLCD cable (XL single-tool)

難易度
ほどほど
利用可能な言語

内容

プリンターメンテナンス

How to replace a Z-axis linear rail (XL)
How to replace the CoreXY plastic parts
How to replace the tch-profile-insert (XL)
How to replace trapezoid nuts (XL)
How to replace Nextruder heatsink (XL Multi-tool)
How to lubricate the coupler pins on Original Prusa XL (Multi-Tool)
How to replace the Sandwich Board (XL)
ネクストルーダーV6ノズルアダプターの取り付け方法 (XLマルチツール)
How to change the belt (XL)
How to replace a hotend heater (XL Single-Tool)
How to replace a PSU (XL)
How to install the Nextruder V6 Nozzle Adapter (XL single-tool)
How to replace the Prusa Nozzle (XL single-tool)
How to replace the Hotend assembly (XL single-tool)
Packing printer for transport - Original Packing Material (XL)
How to replace a Z-axis motor (XL)
How to replace a print fan (XL single tool)
How to clean the side filament sensor (XL)
How to replace a hotend thermistor (XL Single-Tool)
How to replace the main cable connector cover (XL)
How to replace the rubber band on Original Prusa XL (Multi-tool)
How replace the CoreXY Cover Rear (Original Prusa XL)
Packing the XL Enclosure for return - Original Packing material
Prusaノズル（XLマルチツール）の交換方法
Packing the XL Multi-tool for return - Original Packing material
How to fix Modular bed error (HW solution)
How to replace the Hotend assembly (XL multi-tool)
How to replace a profile insert (XL)
How to replace a XY motor (XL)
How to replace a heatbed tile and a heatbed tile cable (XL)
How to change xLCD and xLCD cable (XL single-tool) [進行中の翻訳]
1. 組み立てを始める
2. Introduction
3. Accessing the electronics
4. Disconnecting the cables
5. Removing the xLCD cables
6. Removing the filament sensor and the spool holder
7. Removing the xLCD cables II
8. Disconnecting the xLCD cable
9. xLCD PEケーブルの取り外し
10. Removing the xLCD
11. xLCD parts preparation
12. xLCD parts preparation
13. xLCD assembly
14. Attaching the xLCD
15. Aligning the LCD
16. xLCD assembly versions
17. Connecting the xLCD PE cable
18. Connecting the xLCD cable
19. Routing the xLCD cable
20. Routing the cables
21. Horizontal cable inserting
22. Corner frame cover
23. Inserting Z-motor-cable-bottom-cover
24. Connecting the xLCD cable
25. Covering the electronics
26. Mounting the filament sensor and the spool holder
27. Well done!
How to replace a Dwarf board (XL multi-tool)
How to replace a Dwarf board (XL single-tool)
How to replace the hotend fan (XL Multi-tool)
How to lubricate linear bearing rails (XL)
How to change the xLCD (XL)
How to set up a Buddy3D Cam
How to replace Nextruder heatsink (XL Single-tool)
How to replace a Nextruder (XL)

ログインしてコメントを投稿する

コメントなし

1. 組み立てを始める

難易度

利用可能な言語

内容

プリンターメンテナンス

コメント

1. 組み立てを始める

難易度

利用可能な言語

内容

プリンターメンテナンス

コメント