日本語

1. 組み立てを始める

Step 1 of 24 (Chapter 24 of 39)

内容

難易度
ほどほど
利用可能な言語

内容

プリンターメンテナンス

How to replace a Z-axis linear rail (XL)
How to replace the CoreXY plastic parts
How to replace the tch-profile-insert (XL)
How to replace trapezoid nuts (XL)
How to replace Nextruder heatsink (XL Multi-tool)
How to lubricate the coupler pins on Original Prusa XL (Multi-Tool)
How to replace the Sandwich Board (XL)
ネクストルーダーV6ノズルアダプターの取り付け方法 (XLマルチツール)
How to change the belt (XL)
How to replace a hotend heater (XL Single-Tool)
How to replace a PSU (XL)
How to install the Nextruder V6 Nozzle Adapter (XL single-tool)
How to replace the Prusa Nozzle (XL single-tool)
How to replace the Hotend assembly (XL single-tool)
Packing printer for transport - Original Packing Material (XL)
How to replace a Z-axis motor (XL)
How to replace a print fan (XL single tool)
How to clean the side filament sensor (XL)
How to replace a hotend thermistor (XL Single-Tool)
How to replace the main cable connector cover (XL)
How to replace the rubber band on Original Prusa XL (Multi-tool)
How replace the CoreXY Cover Rear (Original Prusa XL)
Packing the XL Enclosure for return - Original Packing material
Prusaノズル（XLマルチツール）の交換方法
1. 組み立てを始める
2. Introduction
3. Necessary tools
4. Preparing the printer
5. Cleaning the hotend
6. Parking the tool
7. Protecting the heatbed
8. Removing the Nextruder
9. Disconnecting the hotend
10. Removing the hotend
11. Prusaノズルの取り外し
12. Installing the Prusa Nozzle: parts preparation
13. Installing the Prusa Nozzle
14. Inserting the hotend
15. Connecting the hotend
16. Docking the Nextruder
17. Final check
18. Setting the nozzle diameter
19. Tool Offset Calibration
20. Tool Offset Calibration - Sheet install
21. Tool Offset Calibration - pin installation
22. Tool Offset Calibration - Done
23. Calibration pin
24. It's done
Packing the XL Multi-tool for return - Original Packing material
How to fix Modular bed error (HW solution)
How to replace the Hotend assembly (XL multi-tool)
How to replace a profile insert (XL)
How to replace a XY motor (XL)
How to replace a heatbed tile and a heatbed tile cable (XL)
How to change xLCD and xLCD cable (XL single-tool)
How to replace a Dwarf board (XL multi-tool)
How to replace a Dwarf board (XL single-tool)
How to replace the hotend fan (XL Multi-tool)
How to lubricate linear bearing rails (XL)
How to change the xLCD (XL)
How to set up a Buddy3D Cam
How to replace Nextruder heatsink (XL Single-tool)
How to replace a Nextruder (XL)

ログインしてコメントを投稿する

コメントなし

1. 組み立てを始める

難易度

利用可能な言語

内容

プリンターメンテナンス

コメント

1. 組み立てを始める

難易度

利用可能な言語

内容

プリンターメンテナンス

コメント