日本語

1. 組み立てを始める

Step 1 of 61 (Chapter 38 of 39)

内容

How to replace Nextruder heatsink (XL Single-tool)

難易度
ほどほど
利用可能な言語

内容

プリンターメンテナンス

How to replace a Z-axis linear rail (XL)
How to replace the CoreXY plastic parts
How to replace the tch-profile-insert (XL)
How to replace trapezoid nuts (XL)
How to replace Nextruder heatsink (XL Multi-tool)
How to lubricate the coupler pins on Original Prusa XL (Multi-Tool)
How to replace the Sandwich Board (XL)
ネクストルーダーV6ノズルアダプターの取り付け方法 (XLマルチツール)
How to change the belt (XL)
How to replace a hotend heater (XL Single-Tool)
How to replace a PSU (XL)
How to install the Nextruder V6 Nozzle Adapter (XL single-tool)
How to replace the Prusa Nozzle (XL single-tool)
How to replace the Hotend assembly (XL single-tool)
Packing printer for transport - Original Packing Material (XL)
How to replace a Z-axis motor (XL)
How to replace a print fan (XL single tool)
How to clean the side filament sensor (XL)
How to replace a hotend thermistor (XL Single-Tool)
How to replace the main cable connector cover (XL)
How to replace the rubber band on Original Prusa XL (Multi-tool)
How replace the CoreXY Cover Rear (Original Prusa XL)
Packing the XL Enclosure for return - Original Packing material
Prusaノズル（XLマルチツール）の交換方法
Packing the XL Multi-tool for return - Original Packing material
How to fix Modular bed error (HW solution)
How to replace the Hotend assembly (XL multi-tool)
How to replace a profile insert (XL)
How to replace a XY motor (XL)
How to replace a heatbed tile and a heatbed tile cable (XL)
How to change xLCD and xLCD cable (XL single-tool)
How to replace a Dwarf board (XL multi-tool)
How to replace a Dwarf board (XL single-tool)
How to replace the hotend fan (XL Multi-tool)
How to lubricate linear bearing rails (XL)
How to change the xLCD (XL)
How to set up a Buddy3D Cam
How to replace Nextruder heatsink (XL Single-tool) [進行中の翻訳]
1. 組み立てを始める
2. Introduction
3. Tools necessary for this guide
4. Additional parts
5. Filament unloading
6. Printer preparing
7. Protecting the heatbed
8. PTFE unplugging
9. Wi-Fi antenna detaching
10. Disconnecting the Nextruder cable
11. Dock detaching
12. Nextruder releasing
13. Nextruder detaching
14. Cable bundle removing
15. Nextruder body removing
16. Dwarf door opening
17. Heatsink fan removing
18. Nextruder idler opening
19. Gearbox & motor assembly removing
20. Hotend assembly removing
21. Heatsink assembly removing
22. Print fan removing
23. Idler-swivel removing
24. NTC thermistor & Hall sensor removing
25. Filament sensor removing
26. Heatsink: parts preparation
27. Hall sensor installing
28. Filament sensor installing
29. Idler-swivel & NTC thermistor: parts preparation
30. Idler-swivel securing
31. NTC thermistor securing
32. Gearbox & motor assembly: parts preparation
33. Heatsink placing
34. Gearbox disassembling
35. Gearbox assembling
36. PG-ring assembling
37. Gearbox inserting
38. PG assembly alignment
39. Gears lubricating
40. Gearbox covering
41. Nextruder cables connecting
42. Print fan assembly & fitting: parts preparation
43. Print fan assembly securing
44. Fitting securing
45. Hotend & nextruder body: parts preparation
46. Nozzle assembly securing
47. Nextruder body securing
48. Hotend fan securing
49. Dwarf door closing
50. Cable bundle securing
51. エクストルーダーの取り付け：部品の準備
52. Nextruder attaching
53. Nextruder securing
54. Dock securing
55. Nextruder cable connecting
56. Wi-Fi antenna: parts preparation
57. Wi-Fi antenna attaching
58. エクストルーダーPTFEチューブをガイドする
59. Wizard
60. Calibrating the Nextruder gears
61. Well done!
How to replace a Nextruder (XL)

ログインしてコメントを投稿する

コメントなし

1. 組み立てを始める

難易度

利用可能な言語

内容

プリンターメンテナンス

コメント

1. 組み立てを始める

難易度

利用可能な言語

内容

プリンターメンテナンス

コメント