日本語
Login
3Dプリンター
マテリアル
部品 & アクセサリー
ソフトウェア
3Dモデル
応用事例
コミュニティ
ヘルプ
アカデミー
ブログ
会社概要
サポート
Original Prusa XL
プリンターメンテナンス
How to replace a Z-axis motor (XL) | 組み立てを始める
1. 組み立てを始める
Step 1 of 46 (Chapter 16 of 39)
フルスクリーンモード
内容
コメント
難易度
難しい
利用可能な言語
組み立てを始める
内容
プリンターメンテナンス
How to replace a Z-axis linear rail (XL)
How to replace the CoreXY plastic parts
How to replace the tch-profile-insert (XL)
How to replace trapezoid nuts (XL)
How to replace Nextruder heatsink (XL Multi-tool)
How to lubricate the coupler pins on Original Prusa XL (Multi-Tool)
How to replace the Sandwich Board (XL)
ネクストルーダーV6ノズルアダプターの取り付け方法 (XLマルチツール)
How to change the belt (XL)
How to replace a hotend heater (XL Single-Tool)
How to replace a PSU (XL)
How to install the Nextruder V6 Nozzle Adapter (XL single-tool)
How to replace the Prusa Nozzle (XL single-tool)
How to replace the Hotend assembly (XL single-tool)
Packing printer for transport - Original Packing Material (XL)
How to replace a Z-axis motor (XL) [進行中の翻訳]
組み立てを始める
Introduction
Necessary tools
Unloading filament
Preparing the printer - removing side accessories
Printer preparing
Disassembling side filament sensor
Removing the frame-rear-cover
Disconnecting the electronics
Uncovering the electronics
Disconnecting the Z-axis motor cable
Placing the printer
Uncovering the Z-axis motor cable - bottom
Uncovering the Z-axis motor cable - rear
CAUTION: Lubricant Handling
Releasing the Z-axis motor - part 1
Releasing the Z-axis motor - part 2
Pulling out the Z-axis motor
New motor: parts preparation
Installing the trapezoid nut: installing the nut
Installing the trapezoid nut: Z-axis motor attaching
Securing the Z-axis motor: parts preparation
Securing the Z-axis motor
Securing the trapezoid nut
Securing the Bed-frame
Covering the Z-axis motor - bottom
Covering the Z-axis motor - rear
Turning the printer
Tightening the frame-rear-cover
Connecting the Z-axis motor cable
Securing cables (left)
Securing cables (right)
Overview of electronics wiring
Electronics cover back: parts preparation
Covering the electronics
Covering the XLBuddy
Connecting the Nextruder cable
Preparing the Filament sensor
Attaching the filament sensor
Installing the Wi-Fi antenna: parts preparation
Installing the Wi-Fi antenna
Assembling the spool holder: parts preparation
Assembling the spool holder
Mounting the spool holder assembly
XYZ calibration
Good Job!
How to replace a print fan (XL single tool)
How to clean the side filament sensor (XL)
How to replace a hotend thermistor (XL Single-Tool)
How to replace the main cable connector cover (XL)
How to replace the rubber band on Original Prusa XL (Multi-tool)
How replace the CoreXY Cover Rear (Original Prusa XL)
Packing the XL Enclosure for return - Original Packing material
Prusaノズル(XLマルチツール)の交換方法
Packing the XL Multi-tool for return - Original Packing material
How to fix Modular bed error (HW solution)
How to replace the Hotend assembly (XL multi-tool)
How to replace a profile insert (XL)
How to replace a XY motor (XL)
How to replace a heatbed tile and a heatbed tile cable (XL)
How to change xLCD and xLCD cable (XL single-tool)
How to replace a Dwarf board (XL multi-tool)
How to replace a Dwarf board (XL single-tool)
How to replace the hotend fan (XL Multi-tool)
How to lubricate linear bearing rails (XL)
How to change the xLCD (XL)
How to set up a Buddy3D Cam
How to replace Nextruder heatsink (XL Single-tool)
How to replace a Nextruder (XL)
コメント
ログイン
してコメントを投稿する
コメントなし