EN
Login- Čeština
- Español
- Italiano
- Deutsch
- Polski
- Français
- 日本語
- Home
- About your printer
- Printer features
- Print statistics
Print statistics
Menu
- Printer description
- Printer features
- Accelerometer (MK4/S, MK3.9/S)
- Brightness adjustment (SL1)
- Buddy firmware-specific G-code commands
- Cancel Object (MK4/S, MK3.9/S, XL, MINI/+)
- Crash detection
- Crash dump
- Creating a resin calibration object (SL1/SL1S)
- Dump memory (MK3/S/+ and MK2.5/S)
- Experimental menu (MK3/S/+)
- Experimental settings (MK4/S, MK3.9/S, MK3.5/S, XL, MINI/+)
- Filament sensor (MK4, MK3.9, XL)
- Filament sensor MK3 (non-S)
- Flashing custom firmware (MK4/S, MK3.9/S, MK3.5/S)
- Flexible steel sheets (guidepost)
- GPIO Module
- High flow print head (HT90)
- High temperature print head (HT90)
- HW setup (MINI/MINI+)
- HW setup (MK2.5/S & MK3/S/+)
- Internet connection (SL1/SL1S)
- IR Filament Sensor (MK2.5S, MK3S/+, MK3.5/S)
- IR Filament sensor detection (MK3S)
- LCD brightness adjustment (MK3S)
- LCD screen contrast adjustment (i3)
- Loadcell (MK4/S, MK3.9/S, XL)
- Menu structure (SL1/SL1S)
- MMU3 Prusa Nozzle vs. CHT nozzle
- Model preview
- Network Connection (MK4S, MK3.9S)
- Nextruder silicone sock (XL, MK4, MK3.9)
- NFC antenna
- Noisy filament sensor (MINI)
- One-click print
- Pouring resin and starting print
- Power Panic
- Power-modes
- Print Profile (SL1/SL1S)
- Print statistics
- Printer statistics and system information (SL1/SL1S)
- Pronterface and USB cable
- Prusa firmware-specific G-code commands
- Prusa Pro Filament Drybox
- Resin Calibration (SL1/SL1S)
- Resin Tank Cleaning (SL1/SL1S)
- Satin steel sheet
- SD card sorting
- Smooth Steel Sheet
- Sound mode (MINI/MINI+)
- Special PA Nylon steel sheet
- SpoolJoin (MMU2S)
- Steel sheet profiles
- Stuck filament detection #26101 (MK4S) #13101 (MK4) #21101 (MK3.9) #17108 (XL)
- Support menu (MK3/S/+)
- Support settings for the XL
- Textured steel sheet
- Thermal model calibration
- Tools Mapping (XL)
- Tools Mapping and Filament Mapping (XL, MMU3)
- Top-bar Notifications (SL1/SL1S)
- Touch screen (MK4/S, MK3.9/S, MK3.5/S, XL)
- Tune Menu
- Water-soluble materials (PVA/BVOH)
- General Information
This article is also available in following languages: 
The printer tracks printing statistics. When you access this option during a print, you will see statistics for the running print. If you do so while the printer is idle, you will see the total statistics. Both filament usage and print time are tracked.
You can find this menu in the LCD Menu -> Statistics. The data can be easily reset once you do a Factory reset (MK2S/MK2.5S/MK3S).
Was this article helpful?
Comments
Still have questions?
If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.